Simple. Adjust the saddle and repeat the steps above until the notes are the same. The Learn And Master Guitar Setup & Maintenance course is perfect for the discerning guitarist. Adjust the bridge saddle to compensate for flatness or sharpness until the note at the 12th fret is in tune with the open string note. I used to be a full-time guitar instructor and had taught hundreds of people how to play the guitar. Traditional Strat bridges are strung through the back body and up through the block of the tremolo. Make any tweaks after you play it for a few minutes and listen for rattles or buzzing. To do this, remove the plate on the back of your guitar to access the tremolo springs. First of all you may be asking, “what is intonation”? You want to check the nut slots to see if any are too low that strings might be resting or buzzing on the first fret when the neck relief was adjusted straight. The .009″ gauge and the .010″ gauge should slide through with no resistance while the .011″ gauge will slightly move the string. Then retune the string to pitch. Then adjust the screws that secure the tremolo claw to the body tighter or looser to change the gap at the back of the tremolo. // ]]> In order to make adjustments to the action of the nut, you will need a set of files, one that coincides with the width of each string rut in the nut, a feeler gauge, a tuner, and some time and a whole lot of patience. After everything is secure and cleaned up we can throw on the new strings! To straighten the neck you want to check how much relief there is first. The most important areas to lubricate are the slots in the nut, the bridge pieces anywhere the string touches and the pivot points on the tremolo. We did this step already in the evaluation so most of the time the neck is already straight and ready to go, but if not, repeat the process we went through above until the neck is straight and there is a .005″ gap of relief between the bottom of the E strings and the top of the 7th fret. I would also suggest pulling them away from the strings a little bit and listen to the difference in sound. There’s no need to measure the distance of each pole piece as the pole pieces are not individually adjustable. Sometimes after you let the instrument sit overnight the adjustment will change slightly as the neck settles in. The pitch should be the same. From here you can lower each slot until you feel each string is low and comfortable enough for your playing style. If you are not comfortable or have the right tools then please let a qualified luthier or repair shop do this for you. Then I like to raise the pickups until they are very close to the strings and listen to how the magnetic pull causes tonal changes and loss of sustain. To level the front of the 6-screw tremolo pull the tremolo arm up until the back of the bridge is flush with the body. The easiest way to do this is to capo the strings at the first fret, loosen strings at the tuner, take out neck screws, pull the neck out of the body slightly in order to adjust the neck. Today we are going to go look at one of the most iconic guitars in history; the Fender Stratocaster. If the note is sharp use a Phillips screwdriver and move the bridge saddle farther away from the nut or toward the back of the bridge plate. If there are issues like this at the nut or you prefer a different material, then it will have to be taken out to be either replaced or shimmed. After the initial evaluation of the guitar is finished, and we didn’t run into any issues listed above, then we can continue by removing the old strings and giving the guitar a good cleanup. This is a handy guide to setting up your Fender Stratocaster guitar. Make sure you adjust each side of the bridge saddle evenly so that it stays level with the bridge or tremolo plate. Select a file that best fits the fret, and file the fret down a small amount. Don’t cut the B and high E, but just use the whole string to make sure you have the correct string break behind the nut for them since they are smaller in diameter than the wound ones. You can use 0000 steel wool or a 320 grit Klingspor pad to polish the frets and break up any dirt that might be on the fingerboard. Start by loosening the string, not taking it off. By adjusting the string height from the fretboard, you can get the perfect tone and improve your playing. Then I back the pickups off until I can hear that they are no longer influencing the vibration of the string. Pull the string to the tuner. On the Two-Point tremolo simply adjust the pivot screws until the front of the bridge is level with the pick guard. Adjust the height if needed by fine tuning the height on each bridge sadle. Remember to never force the truss rod! ultimate quickstart guide to learning the guitar, Things to Take Note of When Travelling With Your Guitar, Tips to Connecting Scale Patterns And Playing Fluently, How to Play Artificial And Pinch Harmonics, Blues Shuffling Patterns And Progressions In Different Keys, Setting the Action for Better Playability on Your Guitar, Setting Your Guitar Truss Rod to Avoid Bent Necks. Using a ruler or a string action gauge card and holding the guitar in playing position, measure from the top of the 12th fret to the bottom of the string. You want to go through the guitar and find out as many possible problems beforehand so they can be properly fixed or addressed so you don’t waste any time going back to correct them later on. To check the string height first make sure your guitar is properly tuned. It is a chain reaction, and one that is often overlooked by many guitarists who blame these problems on either the tuners themselves, or the bridge action height, both of which are close to the source but not quite the exact problem. Adjust the truss rod until the feeler gauge fits between the bottom of the string and the fret. It is best to start slow and a little higher to make sure you don’t go too low and cause the string to buzz on top of the first fret when played open. To allow the strings to clear the top of the first fret, the bottoms of the slots should be .030" higher than the fret height. Then apply a nut sauce or lubricant to each slot to keep the strings moving freely and prevent any binding. I also like to throw some lubricant on the areas of the E and B string that rests under the string tree to help prevent any dragging there and keep the string moving freely. To check the adjustment make sure the guitar is tuned properly and then affix a capo behind the 1st fret of the guitar. This is where our Big Bends Nut Sauce comes into play. With the new strings on and stretched, we can adjust the neck. I measured the relief at the 7th fret using both a straight edge, and also using the capo at first fret, pressing the last fret on the A string, and measuring the relief at the 7th fret. I would suggest using that as a starting point and then listen to the strings as you play the guitar unplugged. If the fretted note is lower or flatter, then the saddle needs to move forward. Intonation affects how well your guitar plays in tune along the entire length of the fretboard. You will then need to grab your truss rod tool and turn the truss rod nut clockwise until that gap is gone on the bottom edge of the ruler. I like to adjust each string a little lower as I move from bass side to treble side so they get a little closer to the fret on each string. //